Audio Technica AT-LP120-USB Spezifikationen PDF herunterladen (Seite 9)

Turntable operates but emits no sound or not enough sound.

The

stylus guard

still

place. Remove the stylus guard.

The tone arm

the lift position. Lower the tone arm.

Mixer/amplifier (system) controls

are

set incorrectly: wrong input

selected, tape monitor on, speakers switched off, etc. Verify

proper control settings.

Stylus

broken or missing. Check the stylus assembly

and

replace if necessary.

The

stylus assembly may not

fully seated

the cartridge body.

Check the cartridge

and

adjust if necessary.

The

pre-amp selector switch

set

the wrong position. Verify

that it

set for proper output to match mixer/amplifier.

sound/very weak sound: Phono Out setting into

Aux/Line input.

- Very loud/distorted sound: Line Out setting into a

Phono input.

Turntable operates but stylus "skips" across record.

The

stylus guard is still

place. Remove the stylus guard.

The

tracking force

set too light. Set tracking force per cartridge

manufacturer's recommendation.

The tracking force

set too heavy (stylus assembly

bottoming

out

record). Set tracking force per cartridge manufacturer's

recommendation.

The

anti-skate control

set improperly. Verify anti-skate

set for

same value

cartridge tracking force.

5 Turntable

picking up excessive vibrations from floor, walls, or

nearby speakers. Reduce vibrations or place turntable

~turdy/

solid surface.

Tips For Better Performance

Troubleshooting

Record sounds

too

fast or

too

slow.

Turntable

set for wrong speed. Make proper speed selection for

record type being played with platter speed buttons.

Variable pitch

engaged. Depress quartz button or return pitch

adjust slider to center detent position to engage quartz lock.

Moving pitch adjust slider produces no effect.

If the

LED

next to the pitch adjust slider center detent position remains

green when the slider

moved, quartz lock

engaged. Depress the

quartz button to disengage the quartz lock

and

activate variable pitch.

The

LED

should turn

RED.

Strobe dots are difficult

see and/or stylus illuminator

very

dim.

Excessively bright

fluorescent light interferes with strobe

indicator. Hold

hand,

record jacket, etc. over strobe indicator to

shield it from bright light.

Voltage selector switch

set for 230V when

mains

are

115V.

Disconnect

power cord

and

reset the voltage selector switch

located under the platter. (Note: Even with the voltage selector

set for 230V when

mains

are

115V, the quartz lock will bring

the platter up to proper speed.)

•

When

opening or closing the turntable cover, handle it gently,

moving it either at the center or equally

from

both sides.

not

touch the stylus

tip

with

your fingers; avoid bumping

the stylus on the turntable

mat

or a record's edge.

Clean

the

stylus

tip

frequently, using a

soft

brush and a back-

to-front

motion.

• If you use a stylus cleaning fluid, use it sparingly.

• Wipe the

dust

cover and turntable housing gently

with

soft

cloth. Use only a small

amount

mild

detergent

solution

clean the turntable and

dust

cover.

•

Never

apply harsh chemicals or solvents to any part of the

turntable system.

Prior

moving the turntable, always unplug it

from

the

outlet

and lock the

tone

arm on the tone arm rest.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 27 28

Kommentare zu diesen Handbüchern

Keine Kommentare

Audio Technica AT-LP120-USB Spezifikationen Seite 9

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Audio-Plattenspieler Audio Technica AT-LP120-USB